Version=4

[General]
Name="VeriSplint OS 71174 Rev D"
;____________________________________________________
[:/385nm/General]
Printer Classes=["Pico UV385", "PRO UV385", "MAX UV385", "PRO 4K UV385"]

[:/385nm/Curing]
Burn-In Layers=1
Burn-In XY Compensation = -0.20 ; mm
XY Compensation/@4-= 0.000
Light Intensity Control=1
Light Intensity=5.0
Multiplier=1
Offset=0.10

; T [mW/cm²·s , mm] ;Cure Table for 385 Printers
Z=[5.0, 0.00]
Z=[10.0, 0.13]
Z=[15.0, 0.24]
Z=[20.0, 0.31]
Z=[25.0, 0.37]
Z=[30.0, 0.42]
Z=[35.0, 0.46]
Z=[40.0, 0.50]
Z=[45.0, 0.53]
Z=[50.0, 0.56]
Z=[100.0, 0.78]
Z=[150.0, 0.90]

[:/385nm/Mechanics]
Approach Pressure Limit=100.0
Approach Velocity=10.0
Layer Tolerance=15.0
Motor Timeout=60.0
Separation Pressure Limit=500.0
Separation Velocity=10.0
Slides Per Layer=0
Traverse Timeout Range=0.30

[:/385nm/General]
Slice Thickness Presets=[0.050,0.075,0.100]

;____________________________________________________
[:/PRO-Platform/General]
Printer Classes=["PRO UV385", "Pico UV385"]

[:/PRO-Platform/Curing]
Burn-In Exposure=0.35 ; mm
Shrinkage Compensation Enable=false ; true/false
XY Scale = 1.0102

[:/PRO-Platform/Delays]
Normal Wait Time (After Approach)=1 ; s
Normal Wait Time (After Separation)=1 ; s
;____________________________________________________
[:/MAX-Platform/General]
Printer Classes=["MAX UV385"]

[:/MAX-Platform/Curing]
Burn-In Exposure=0.60 ; mm
XY Scale = 1.0093
;____________________________________________________
[:/PRO4K-Platform/General]
Printer Classes=["PRO 4K UV385"]

[:/PRO4K-Platform/Curing]
Burn-In Exposure=0.40 ; mm
XY Scale = 1.0100
;____________________________________________________

[Support]
Type="SupportDialog"
Version=1

[Support/Geometry]
Aspect Ratio=3.0
Contact=0.5
Half Contact=false
Island=0.5
Maximum Width=2.3
Overshoot=3.0
Side Faces=20
Undershoot=0.0

[Support/Lattice]
Connect Gap=2
Connection=3
Enabled=false
Layout=3
Margin=0.5
Spacing XY=3.0
Spacing Z=5.0

[Support/Placement]
Accuracy=0.0
Intersupport=false
Minimum Height=0.0
No Fill=false
Rank Distance=false
Side Feature=2.0
Slope=20
Spacing=3.0
Strength=40
Torsion=0

[Support/SupportParts]
Leveling=true
Leveling Height=2.0
Tallest=false
Tallest Height=0.0

[Support/Geometry/Contact]
@=0.6

[Support/Geometry/Island]
@=2.0

[Support/Geometry/Maximum Width]
@=2.0
@Lattice=1.0

[Support/Geometry/Overshoot]
@=0.7

[Support/Lattice/Connect Gap]
@=1

[Support/Lattice/Connection]
@Flexible=0

[Support/Lattice/Enabled]
@=true
@Flexible=true
@Lattice=true

[Support/Placement/Intersupport]
@Flexible=false
@Lattice=false

[Support/Placement/Slope]
@=50